| 1.Brick machine installation location | | | | gap, so as to avoid collision between vibration and |
| Burning-free brick machine installation layout should be | | | | debugging After a good position to promote the |
| based on production sites, product process | | | | fixed rack plate. Skip back, raised his head pressure, |
| requirements to determine, in principle, required | | | | die box, start sending trigger to send board, observe |
| back-mixing on the material, sent board, the host | | | | whether the card block pallets forward into the |
| forming, sending bricks, conservation, and pallet flow | | | | machine after the shaking table is correct place. |
| interference from each other, the proposed | | | | Correct locking bolts after adjustment. Adjust the |
| installation of the foundation plan by row cloth. | | | | speed of advance and retreat to send board |
| 2. the main machine installation | | | | configuration throttle to achieve, must be sent with |
| Including the main machine frame, shaking table, | | | | the brick adjustments meet the latter. Normal |
| hopper, model boxes and punch down and die and | | | | pre-production, test each batch of pallet size should |
| other components. Check the mechanical installation | | | | match the size of deviations in the permitted range |
| should be carefully whether the bumps during | | | | can be used. |
| transport, damaged, lost or missing pieces of the | | | | 4. sending brick installation |
| relative position change. The main machine should be | | | | Get a good block and brick for forming pallet |
| installed pre-cast foundation in place to install, | | | | conveyor, conveyor belt speed can not be adjusted. |
| configure, vibration isolation pads, locking bolt. | | | | Installation, its axis should be the same machine axis |
| Installation, application level strict leveling instrument | | | | vibration table, vibration table surface height and the |
| (in the range of machine ground plane corner, | | | | same height. In order to facilitate cleaning, and basic |
| diagonal High Low ≤ 1mm), to ensure the quality | | | | fixed without sending brick, start the machine in place |
| of block molding machine. The hydraulic piping and | | | | to send bricks 2-3 plates, if the stable block and pallet |
| electric control lines required to connect, the | | | | conveying, no deviation can be used, the specific |
| confirmation, which require users to connect | | | | action time set by conveyor belt connection to send |
| electronic control electronic control box location based | | | | bricks to send board action action does not produce |
| care through buried pipe lines, to avoid personal injury | | | | a smooth transition between the subject jumps hit, |
| or shock control signal disorder. | | | | and just OK with brick pallets up to the circuit |
| In turn start the power, close the switch, set to | | | | breakers Taiwan. |
| manual control console, open the oil pump, steering | | | | 5. mechanical, electrical, hydraulic linkage |
| pump and check whether the anomaly, when the | | | | Other ancillary equipment and manually installed after |
| motor switch to normal, upper and lower buck to | | | | the adoption of automatic control of linkage should |
| move the control head, sub head-oriented set of | | | | be empty, run the 5-10 board, observe the action, |
| observations along the guide column is running No | | | | layout, spacing and indicator light shows the |
| card balance resistance, pull rub, fever phenomenon, | | | | confirmation, debugging is completed. |
| mold box and pressure head may not have collision, | | | | 6. pilot production and high degree of control block |
| check with the gap is uniform, relative motion is | | | | The concrete brick machine after installation, should |
| smooth without abnormal friction. | | | | be feeding trial production, a serious observation of |
| 3. sent to board plane to install Debugging | | | | the movement is accurate in place machinery. Check |
| Send trigger the same axis with the main frame, | | | | the quality of molding products, adjust the charge |
| adjust the pad to send a pallet rack fit orbital plane, | | | | head stopper, forming a block height to the height |
| note sent with the shaking table board machine | | | | required. |
| frame between the left side combination of 5-10mm | | | | |